Air flushing provides an efficient method of removing debris from pipelines and newly constructed systems.

  • In the gas process lines, the velocity should be the lowest figure between 60 m/s and the velocity obtained at 1.3 time the maximum process flow rate. The minimum velocity should be 30 m/s.
  • In liquid process lines, a velocity between 30 m/s and 60 m/s should be used.

Air Blowing 과 같이 청소을 목적으로 합니다. Air Blowingr과 Air Flushing의 차이라면 Air Blowing은 압력을 채워 한번에 배출하고, Air Flushing은 연속적으로 순환시켜 오염물질을 청소하는 것으로 이해하시면 될 것 입니다. 사용되는 방법으로 Air / Steam / Water / Manual / Pigging 등의 여러가지가 있습니다. 아래 JSA는 Air Blowing 큰 차이는 없으니 참고하세요.

Hazard Category Hazards Controls
Injury to Pesonnel and Property Damage 1. As a result of low safety awareness or incorrect information

2. Non compliance of safety regulation & procedures

1. Obtain correct PTW

2. Task supervisor to conduct pre-start meeting on daily basis and discuss all relevant hazard to the job with the crew and  what corrective action are required before/during and at completion of job and sign attendance sheet.

3. Task supervisor to explain JSA to all employees and sign attendances sheet

4. Confirm that procedures and other associated documents are approved and available.

Slips and Trips 1. Cause by inadequate access and poor visibility 1. Ensure proper wind up of hoses and housekeeping at work site.

2. All work areas are to be kept clean and free of tripping hazards.

3. The accessories (hoses & pump) not being used must be disconnected and store separately

4. Adequate lighting for night work is to be provided or when lighting is poor

Serious or Fatal Injury 1. Accidentally sudden release of air pressure & debris from discharge end of pipe or any valve spindle gland, gasket and flange

2. Defective tools can damage equipment and damaged equipment can leak due to high pressure

1. Barricade the area where air blowing test is to be carried out

2. Post warning signs

3. Appropriate PPE (Personnel Protective Equipment) such as safety helmet, safety glasses, leather gloves and safety shoes shall be worn by all employees

4. Ensure the equipment and tools to be used for air flushing (such as hoses, pump, couplings, pressure gauges, gasket etc.) are free from any defect and suitable for the pressure rating of the system

5. Whiplash arrestor must be installed with every joint of hose connector.

Stuck or Hit to personnel 1. Can occur sudden release of air pressure & debris 1. During the testing operation all non essential personnel will be kept out of the test area

2. Provide barricade and signages to prevent entry of unauthorized personnel

Physical Injury from flying debris 1. Flying foreign particles from pipe 1. Pressure gauge must be installed to monitor the allowable pressure

2. A screen should be provided at least 2 meter away from the open end pipe to protect the foreign particles to hit soneone.

3. The area must be cordoned off

 

kassy

Recent Posts

푸꾸옥 여행 Tip.

베트남에 놀러간다면,  푸꾸옥을 놀러간다면 즐거운 여행에 첨가되는 라면스프 같은 소스를 소개합니다. 1. 라오몽 사오또이 동남아…

3일 ago

[20년만의] 마카오 야경

마카오 관광에서 가장 인상 깊다면 야경을 뽑을 수 있습니다. 남쪽 Cotai 지역만 이동하다보니 그렇게 느꼈을지…

7일 ago

비양도

제주도 서쪽 비양도라는 섬이 있습니다. .  비양도는 제주시 한림읍 비양리 위치해 있으며, 하늘에서 날오온 섬이라는 의미를 지니고 있습니다. 비양도는 한림항에서 약 1.1km 떨어져 있으며, 섬의 모양은 원형에 가깝고 약 2000여명의 주민이 거주하고 있습니다. 비양도의 중앙에는 해발 114m 높이의 비양봉 본석구가 있고, 서쪽 해안에는 제주도에서 가장 큰 초대형 화산탄들이 분포하고 있습니다. .  섬의 북쪽 해안에는 호니토(homito)로 알려진 굴뚝모양의 바위들이 약 20여기 분포하고 있다. 호니토는 용암이 흐르다가 습지 등의 물을 만나 수증기와 용암이 뒤섞여 분수처럼 솟구쳐 나와 쌓여 만들어졌으며, 천연기념물 제439호로 지정되어 있습니다. .  섬의 동쪽에는 펄렁못 엄습지와 마을 신당이 위치해 있습니다. 최근까지 비양도는 약 1,000년 전에 분출한 섬으로 알려져 왔으나 용암의 나이를 분석한 결과 27,000년 전에 형성된 것으로 조사되었습니다. . …

3주 ago

조용한 숲속, 원주 감악산

원주에 감악산을 다녀왔습니다. 강원도는 정말 등산을 가는 드라이브 코스부터 산과 계곡이 함께하기 때문에 설레임을 더해줍니다.…

3주 ago

비자림

자연이 살아있는 천년의 숲 비자림 제주 평대리 비자나무 숲 제주 평대리 비자나무 숲(비자림)은 한라산 동쪽에서…

1개월 ago

천연기념물 제420호, 성산일출봉

제주 동쪽 여행의 필수코스. 4년 전, 제주에 놀러왔는데 도착하고 태풍이 올라오고 있었습니다. 섭지코지의 문어빵을 무조건…

1개월 ago